Takura Steel Buildings

Takura Steel Buildings is a leading supplier of Pre-Engineered Metal Buildings and Components.

Insulated Panels

 

 

“Melt-Span panels are economical, offer unlimited design flexibility, and are durable and quick to install.”

Get a Free Quotes

LS-36™ Roof and Wall Panel

The Metl-Span Striated insulated metal wall panel is an attractive and economical alternative to typical flat wall panels. The exterior face is lightly profiled with narrow longitudinal striations and exhibits a virtual flat appearance from a short distance away. The Striated wall panel is an exceptional value combining the aesthetics of a flat wall panel and high insulation ratings of a polyurethane core.

Note: Not intended for exterior walls on cold storage buildings.

Exterior Profile:
Longitudinal striations, nominal 1/32″ deep

Interior Profile:
Mesa nominal 1/8″ deep; Light Mesa nominal 1/16″ deep

Panel Core:
Foamed-in-place, Non-CFC & zero ODP polyurethane, FM Class 1 approval

Thermal Values:
K-factor, Btu in/ft2 hr. °F @ 75°F (24°C) mean core temperature = 0.140
K-factor, Btu in/ft2 hr. °F @ 40°F (4°C) mean core temperature = 0.126

Module Width:
30″, 36″, 42″

Panel Thickness:
2″, 2 1/2″, 3″ (2 3/4″ thickness also available from Nevada plant)

Panel Lengths:
8′-0″ to 40′-0″ for the 30″ & 36″ widths, 8′-0″ to 32′-0″ for the 42″ width

Exterior Facings:
Stucco embossed, G-90 galvanized and/or AZ-50 aluminum-zinc coated steel in 24 Ga. and 22 Ga.

Interior Facings:
Stucco embossed, G-90 galvanized and/or AZ-50 aluminum-zinc coated steel in 26 Ga., 24 Ga. and 22 Ga.

Panel Joint:
Offset double tongue and groove with extended metal shelf for positive
face fastening

Fastening:
Fastener and Clip concealed in the side joint

Color:
A full range of exterior colors & coatings are available for the architectural market. For specific information about our available colors and coatings, visit us online for a comprehensive selection.

Superior Insulating Value across the entire wall and roof area is assured with Metl-Span panels. The advanced polyurethane core provides enhanced insulation values that significantly lower heating and cooling costs.

One-Piece Construction process assures rapid completion of the wall and roof system. Factory fabricated composite panels are attached directly to the supporting structure and multiple steps to construct the insulated wall and roof are eliminated. Faster building completion means reduced construction and interim financing costs.

Lightweight yet Structurally Strong panels weigh only 2 ½ to 3 ½ pounds per square foot but are structurally strong enough for long spans that can significantly reduce costs for frame support.

Impermeable Faces & Built-in Thermal Breaks ensure the highest insulating values are maintained for the life of the building. Panels are manufactured with impermeable faces and when installed the insulation is completely encapsulated by metal trim that creates an impermeable membrane on all sides of the panel. The aged “R” values are comparable to the initial “R” values many years after the building’s original completion. Assured thermal values mean lower heating and cooling costs.

Class 1 Polyurethane Foam meets the requirements of the major model building codes for many types of construction. Unlike panels with expanded polystyrene cores they will not produce a self-propagating fire. Local building codes may require automatic fire suppression systems for most installations.

Concealed Attachment with clips and fasteners at the side joint of the panel offers a clean high profile appearance. No more barn like metal building looks.

Metl-Span are Lightweight, yet very strong and durable attributing to reduced costs for erection and structural support.

Exterior Profile: 1 ¼” high major ribs at 12″ o.c. with Mesas in between ribs at 4″ o.c.
Interior Profile: Mesa nominal 1/8″ deep Panel Core: Foamed-in-place, non-CFC, zero ozone depleting (zero ODP) polyisocyanurate, Factory Mutual Class 1 approval Thermal Values: K-factor, Btu in/ft2 hr. °F @ 40°F(4°C) mean core temperature = 0.126
Module Width: 36″
Panel Thickness: 1 ½”, 2″, 2 ½”, 3″, 4″, 5″, 6″
Panel Lengths: 8′-0″ to 50′-0″
Exterior Facings: Stucco embossed, G-90 galvanized and/or AZ-50 aluminum-zinc coated steel in 26 Ga., 24 Ga. and 22 Ga.
Interior Facings: Stucco embossed, G-90 galvanized and/or AZ-50 aluminum-zinc coated steel in 26 Ga., 24 Ga. and 22 Ga.
Panel Joint: Overlapping with a single tongue and groove Fastening: Exposed through fasteners
Minimum Slope: ½:12

* Fy is 80-ksi reduced to 60-ksi in accordance with the 2007 edition of the North American Specification For Design Of Cold-Formed Steel Structural Members – A2.3.2.

NOTES:

  1. All calculations for the properties of AVP panels are calculated in accordance with the 2012 edition of the North American Specification For Design Of Cold-Formed Steel Structural Members.
  2. Ixe is for deflection determination.
  3. Sxe is for bending.
  4. Maxo is allowable bending moment.
  5. All values are for one foot of panel width.
Panel
Thickness
Support
Condition
Load
Type
Connection Support Spacing
3′ 4′ 5′ 6′ 7′ 8′ 9′ 10′ 11′ 12′ 13′
1 ½” 1-Span Live/Press1 175.59 113.58 77.21 54.36 39.38 29.23 22.17 17.14 13.49 10.77 8.72
Suction wall3,5 210.61 157.96 110.3 77.66 56.25 41.76 31.67 24.49 19.26 15.39 12.46
Suction roof4,5 210.61 157.96 110.3 77.66 56.25 41.76 31.67 24.49 19.26 15.39 12.46
2-Span Live/Press1 185.92 127.93 93.52 70.95 55.2 43.74 35.17 28.62 23.54 19.55 16.37
Suction wall3,5 108.03 78.51 61.45 50.44 42.78 37.15 32.84 29.44 25.75 21.36 18.01
Suction roof4,5 129 93.75 73.38 60.24 51.09 44.37 39.22 31.7 25.75 21.36 18.01
3-Span
and greater
Live/Press1 188.05 128.86 93.09 69.46 53.02 41.21 32.52 26.01 21.06 17.24 14.25
Suction wall3,5 112.65 83.61 66.48 55.2 47.2 41.23 36.61 32.92 29.91 24.62 20.36
Suction roof4,5 134.52 99.84 79.39 65.91 56.36 49.24 43.71 37.16 30.08 24.62 20.36
2″ 1-Span Live/Press1 227.51 151.64 106.13 76.71 56.84 43.01 33.15 25.97 20.66 16.66 13.59
Suction wall3,5 211.67 158.76 127 105.84 81.19 61.44 47.35 37.1 29.51 23.79 19.42
Suction roof4,5 211.67 158.76 127 105.84 81.19 61.44 47.35 37.1 29.51 23.79 19.42
2-Span Live/Press1 236.19 164.77 122.2 94.14 74.39 59.87 48.87 40.34 33.63 28.27 23.94
Suction wall3,5 110.99 80.63 63 51.6 43.68 37.87 33.44 29.94 27.1 24.77 22.8
Suction roof4,5 130.9 95.1 74.3 60.86 51.52 44.67 39.43 35.31 31.97 29.21 26.57
3-Span
and greater
Live/Press1 238.68 166.52 122.72 93.46 72.78 57.63 46.26 37.57 30.83 25.54 21.35
Suction wall3,5 114.6 84.94 67.46 55.96 47.82 41.75 37.06 33.32 30.26 27.72 25.58
Suction roof4,5 135.16 100.18 79.56 66 56.4 49.24 43.71 39.29 35.69 32.7 30.16
2 ½” 1-Span Live/Press1 274.11 186.7 133.59 98.6 74.45 57.28 44.79 35.53 28.56 23.23 19.1
Suction wall3,5 212.74 159.56 127.64 106.37 91.17 79.78 63.98 50.76 40.8 33.18 27.29
Suction roof4,5 212.74 159.56 127.64 106.37 91.17 79.78 63.98 50.76 40.8 33.18 27.29
2-Span Live/Press1 281.2 198.17 148.5 115.65 92.43 75.26 62.14 51.88 43.71 37.12 31.73
Suction wall3,5 113.71 82.68 64.54 52.79 44.61 38.63 34.06 30.46 27.56 25.16 23.15
Suction roof4,5 132.46 96.31 75.18 61.49 51.97 45 39.67 35.49 32.1 29.31 26.97
3-Span
and greater
Live/Press1 283.75 200.43 149.8 115.8 91.54 73.56 59.87 49.25 40.89 34.24 28.89
Suction wall3,5 116.56 86.31 68.48 56.76 48.47 42.3 37.53 33.73 30.64 28.06 25.88
Suction roof4,5 135.78 100.54 79.77 66.12 56.46 49.28 43.72 39.3 35.69 32.69 30.15
3″ 1-Span Live/Press1 314.84 217.99 158.71 119.17 91.44 71.39 56.54 45.37 36.83 30.21 25.03
Suction wall3,5 213.93 160.44 128.36 106.96 91.68 80.22 71.31 64.18 52.61 43.16 35.76
Suction roof4,5 213.93 160.44 128.36 106.96 91.68 80.22 71.31 64.18 52.61 43.16 35.76
2-Span Live/Press1 320.55 227.72 172.01 135.06 108.88 89.45 74.54 62.79 53.38 45.71 39.41
Suction wall3,5 116.21 84.62 66.04 53.97 45.56 39.39 34.7 31 28.02 25.57 23.52
Suction roof4,5 133.67 97.34 75.96 62.07 52.4 45.31 39.91 35.66 32.23 29.41 27.05
3-Span
and greater
Live/Press1 322.96 230.22 173.87 135.94 108.74 88.41 72.79 60.54 50.78 42.93 36.54
Suction wall3,5 118.47 87.67 69.51 57.57 49.13 42.86 38.02 34.16 31.01 28.4 26.2
Suction roof4,5 136.26 100.84 79.95 66.21 56.51 49.3 43.73 39.29 35.67 32.67 30.13
4″ 1-Span Live/Press1 378.17 267.95 200.13 154.26 121.46 97.14 78.69 64.43 53.26 44.41 37.33
Suction wall3,5 216.18 162.13 129.71 108.09 92.65 81.07 72.06 64.85 58.96 54.04 49.89
Suction roof4,5 216.18 162.13 129.71 108.09 92.65 81.07 72.06 64.85 58.96 54.04 49.89
2-Span Live/Press1 381.73 274.53 209.87 166.8 136.16 113.33 95.7 81.74 70.44 61.15 53.41
Suction wall3,5 120.7 88.22 68.93 56.29 47.45 40.95 36 32.11 28.98 26.41 24.26
Suction roof4,5 135.52 99.05 77.39 63.2 53.27 45.98 40.42 36.06 32.54 29.65 27.24
3-Span
and greater
Live/Press1 383.63 276.96 212.22 168.62 137.23 113.58 95.19 80.56 68.73 59.04 51.01
Suction wall3,5 122.12 90.35 71.55 59.19 50.46 43.98 38.98 35 31.77 29.08 26.81
Suction roof4,5 137.11 101.45 80.34 66.46 56.66 49.39 43.77 39.3 35.67 32.65 30.11
5″ 1-Span Live/Press1 415.47 298.99 227.37 178.68 143.49 117.03 96.6 80.51 67.66 57.29 48.82
Suction wall3,5 218.31 163.73 130.99 109.16 93.56 81.87 72.77 65.49 59.54 54.58 50.38
Suction roof4,5 218.31 163.73 130.99 109.16 93.56 81.87 72.77 65.49 59.54 54.58 50.38
2-Span Live/Press1 417.57 303.13 233.87 187.56 154.5 129.79 110.67 95.46 83.1 72.89 64.33
Suction wall3,5 124.82 91.61 71.74 58.63 49.4 42.59 37.4 33.31 30.02 27.32 25.07
Suction roof4,5 136.75 100.36 78.59 64.23 54.12 46.66 40.97 36.49 32.89 29.93 27.46
3-Span
and greater
Live/Press1 418.89 305.08 236.09 189.66 156.22 130.96 111.22 95.4 82.49 71.79 62.83
Suction wall3,5 125.71 93.07 73.67 60.89 51.87 45.17 40 35.9 32.56 29.79 27.46
Suction roof4,5 137.72 101.95 80.71 66.71 56.82 49.48 43.82 39.33 35.67 32.64 30.08
6″ 1-Span Live/Press1 323.41 242.55 194.04 161.7 138.6 121.28 107.8 91.59 78.13 67.1 57.96
Suction wall3,5 220.56 165.42 132.34 110.28 94.53 82.71 73.52 66.17 60.15 55.14 50.9
Suction roof4,5 220.56 165.42 132.34 110.28 94.53 82.71 73.52 66.17 60.15 55.14 50.9
2-Span Live/Press1 314.31 231.63 181.92 148.91 125.54 108.23 94.96 84.5 76.08 69.15 63.37
Suction wall3,5 128.61 94.77 74.43 60.93 51.37 44.29 38.86 34.58 31.13 28.29 25.93
Suction roof4,5 137.65 101.44 79.67 65.21 54.98 47.4 41.59 37.01 33.32 30.28 27.75
3-Span
and greater
Live/Press1 308.21 225.94 177.17 145.24 122.86 106.39 93.8 83.87 75.84 69.23 63.68
Suction wall3,5 129.14 95.72 75.79 62.61 53.3 46.38 41.04 36.81 33.37 30.52 28.12
Suction roof4,5 138.22 102.45 81.12 67.02 57.04 49.64 43.93 39.4 35.72 32.66 30.1
  1. Live/Press: Allowable loads applicable to downloads such as roof live, snow, and positive wind pressure.
  2. Allowable values are based on a 36″ wide panel with a 26 Ga. fascia and 26 Ga. liner with 3-1/4″-14 SDS in a 3′ wide panel at each supporting structural member.
  3. Connection for Walls: Screws located at the middle of the low pan centered between the high ribs of the fascia panel. Attach fasciConnection for Roof: Screws located at the middle of the high ribs of the fascia panel with an HW-355 bonded washer under the screw head. Attach fascia sidelaps with 1/4″ Lapteks at 20″ o.c. max. spacing between main panel connections.a sidelaps with 1/4″ Lapteks at 20″ o.c.
  4. Connection for Roof: Screws located at the middle of the high ribs of the fascia panel with an HW-355 bonded washer under the screw head. Attach fascia sidelaps with 1/4″ TheLapteks at 20″ o.c. max. spacing between main panel connections.
  5. Pullout of the self-drilling screws from the supporting structural member must be checked separately.
  6. Allowable values have been derived from tests conducted in accordance with the ASTM E72 and ASTM E1592 test specifications.
  7. Allowable face buckling, shear, and panel pullover loads have been calculated using a 1.875 safety factor derived from test data scatter.
  8. Allowable values include a deflection check against an L/240 limit for Live/Press loading, and an L/240 limit for 10-year wind pressures for Wind Suction loading.
  9. Allowable values shown are intended to be compared against factored loads from ASCE 7-based load combinations.
  10. Allowable loads are given for equally-spaced supports.
  11. This information is subject to change without notice. Pleace contact Metl-Span for most current information.